ASTM E10-18 《金属材料布氏硬度标准试验方法》美国标准 英文版

英文名称:ASTM E10-18.png

ASTM E10-18

Standard Test Method for Brinell Hardness of Metallic Materials


中文名称:

ASTM E10-18

金属材料布氏硬度标准试验方法


替代情况:替代ASTM E10-17


代号说明:

This standard is issued under the fixed designation E10; the number immediately following the designation indicates the year of original

adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript

epsilon (ε) indicates an editorial change since the last revision or reapproval.

This standard has been approved for use by agencies of the U.S. Department of Defense.


版本说明:

1 This test method is under the jurisdiction of ASTM Committee E28 on Mechanical Testing and is the direct responsibility of Subcommittee E28.06 on Indentation Hardness Testing.

Current edition approved July 1, 2018. Published August 2018. Originally approved in 1924. Last previous edition approved in 2017 as E10 – 17. DOI: 10.1520/E0010-18.

2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website.

3 Available from American Bearing Manufacturers Association (ABMA), 2025 M Street, NW, Suite 800, Washington, DC 20036, http://www.americanbearings.org.

4 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036,

http://www.ansi.org.


标准正文


1. Scope


1.1 This test method covers the determination of the Brinell hardness of metallic materials by the Brinell indentation hardness principle. This standard provides the requirements for a Brinell testing machine and the procedures for performing Brinell hardness tests.

1.2 This test method includes requirements for the use of portable Brinell hardness testing machines that measure Brinell hardness by the Brinell hardness test principle and can meet the requirements of this test method, including the direct and indirect verifications of the testing machine. Portable Brinell hardness testing machines that cannot meet the direct verification requirements and can only be verified by indirect verification requirements are covered in Test Method E110.

1.3 This standard includes additional requirements in the following annexes:

Verification of Brinell Hardness Testing Machines        Annex A1

Brinell Hardness Standardizing Machines                     Annex A2

Standardization of Brinell Hardness Indenters              Annex A3

Standardization of Brinell Hardness Test Blocks           Annex A4

1.4 This standard includes nonmandatory information in the following appendixes that relates to the Brinell hardness test:

Table of Brinell Hardness Numbers            Appendix X1

Examples of Procedures for Determining Brinell Hardness Uncertainty           Appendix X2

1.5 At the time the Brinell hardness test was developed, the force levels were specified in units of kilograms-force (kgf). Although this standard specifies the unit of force in the International System of Units (SI) as the Newton (N), because of the historical precedent and continued common usage of kgf units, force values in kgf units are provided for information and much of the discussion in this standard refers to forces in kgf units.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the

Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


2. Referenced Documents


2.1 ASTM Standards: 

A833 Test Method for Indentation Hardness of Metallic Materials by Comparison Hardness Testers

A956 Test Method for Leeb Hardness Testing of Steel Products

A1038 Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method

B647 Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage

E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E74 Practices for Calibration and Verification for Force-Measuring Instruments

E110 Test Method for Rockwell and Brinell Hardness of Metallic Materials by Portable Hardness Testers

E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness

E384 Test Method for Microindentation Hardness of Materials

2.2 American Bearings Manufacturer Association Standard:

ABMA 10-1989 Metal Balls 

2.3 ISO Standards:

ISO/IEC 17011 Conformity Assessment—General Requirements for Accreditation Bodies Accrediting Conformity Assessment Bodies 

ISO/IEC 17025 General Requirements for the Competence of Calibration and Testing 



在线阅读           免费下载
contentHeight = $(".newsContent").height(); if(contentHeight < 615){ contentHeight = 615; }

<script>

var _hmt = _hmt || [];

#xkhks#function#xkhks##xkhjs# {

  var hm = document.createElement#xkhks#"script"#xkhjs#;

  hm.src = "//hm.baidu.com/hm.js?44deb32c2e6840d7a08bc3714ce272b7";

  var s = document.getElementsByTagName#xkhks#"script"#xkhjs#[0]; 

  s.parentNode.insertBefore#xkhks#hm, s#xkhjs#;

}#xkhjs##xkhks##xkhjs#;

</script>